MALIIGAZA IP68 Waterproof COB LED Strip Light - 480 LEDs/m Flexible Weatherproof Outdoor Silicone LED Tape (12V/24V)

Superior COB Architecture vs. Traditional SMD Strips

Traditional Surface Mount Diode (SMD) strips place individual diodes millimeters apart, creating glaring bright spots and dark gaps. MALIIGAZA COB technology mounts light chips directly onto the flexible printed circuit board under a continuous phosphor coating.

• 180-degree beam angle for wider light distribution
• Higher luminous efficacy achieving >100 LM/W
• Reduced operating heat for extended LED lifespan

Flexible, Cuttable & Custom-Fit

Tailor your lighting setup to exact measurements. The FOB-480-IP68 strip can be safely cut at designated cut marks along the length. Paired with our specialized waterproof connectors and end-cap silicone sealant, you can make waterproof L-corner turns, extend runs, or split lines effortlessly.

• Includes heavy-duty self-adhesive backing for quick installation
• Slim 10mm outer silicone sleeve fits neatly into standard channels
• Safe low-voltage operation (12V or 24V DC options)

Step 1: Surface Preparation

Clean the mounting surface thoroughly with rubbing alcohol to remove dust and grease. Ensure the area is completely dry before applying adhesive.

Step 2: Measure & Trim (Optional)

Measure the required length. If cutting is necessary, cut strictly along the copper solder pads marked on the strip. Do not cut anywhere else.

Step 3: Seal Cut Ends (Critical for IP68 Waterproofing)

If cut, attach specialized IP68 waterproof quick connectors or end caps using waterproof silicone sealant to maintain the submersible rating.

Step 4: Mounting

Peel back the protective tape backing and press the strip firmly against the mounting surface. For outdoor overhead applications, we recommend mounting clips for added long-term support.

Step 5: Wiring to DC Power

Connect the strip lead wires to a compatible DC 12V or DC 24V power supply matching your strip voltage specification. Plug the power transformer into the mains supply.

Strip does not illuminate after power-on?

Check polarity (+ and - wires). Low-voltage DC lighting requires correct polarity. Also verify that your transformer output matches the strip voltage (12V vs 24V).

Light dimming or turning off towards the end of long runs?

This indicates voltage drop. Ensure your power supply wattage exceeds the strip total requirements by at least 20-30%. For long continuous runs, feed power from both ends of the strip.

Lights flickering or humming?

Ensure you are using a regulated DC power supply and a compatible PWM dimmer switch. Non-regulated AC transformers will cause flicker.

1. What makes IP68 COB LED strips better than IP65 or IP67 strips?

IP65 strips only protect against water splashes, while IP67 withstands temporary immersion. MALIIGAZA IP68 COB strips utilize a solid silicone extrusion casing that offers complete protection against continuous underwater immersion, high humidity, freezing temperatures, and intense direct sunlight.

2. Does this COB LED strip light come with a power supply transformer?

No, the power supply transformer and LED controllers are not included. You will need to purchase a DC 12V or DC 24V power adapter separately depending on the voltage option you choose.

3. Should I select 12V or 24V for my installation?

For shorter runs up to 5 meters, 12V works exceptionally well. For longer continuous runs over 5 meters, 24V is recommended because higher voltage reduces voltage drop, maintaining consistent brightness along the entire length.

4. Can I cut this waterproof COB LED strip light to custom lengths?

Yes, the strip is cuttable at designated copper solder marks along the PCB. To preserve the IP68 waterproof rating after cutting, you must seal the cut end using waterproof silicone end caps and sealant.

5. Can this waterproof LED strip be submerged in swimming pools or fountains?

Yes, the IP68 rating allows for continuous submersion. Ensure all end connections and power leads are fully sealed with waterproof silicone before submersing into water.

6. How do I dim the MALIIGAZA COB LED strip?

This strip is fully dimmable. You can install an inline DC PWM dimmer switch between the power supply and strip, or use a dimmable LED driver paired with standard wall dimmers (TRIAC/0-10V).

7. Will the silicone tubing turn yellow over time in the sun?

No. Unlike lower-grade PVC coatings used by competitors, MALIIGAZA uses UV-stabilized, high-purity meteorological silicone casing that resists solar degradation, yellowing, and cracking.

8. What power supply wattage do I need for a 5-meter strip?

At 11W per meter, a 5m strip draws 55W. We recommend adding a 30-50% safety margin, meaning you should use a power transformer rated for at least 75W to 80W.

9. Can this strip light be used inside saunas and steam rooms?

Yes, the high-density silicone tubing handles moisture and elevated temperatures, making it suitable for bathroom showers, saunas, and indoor spas.

10. What color temperature should I choose for outdoor garden lighting?

Warm White (3000K) or Warm Yellow (2700K) is ideal for outdoor landscaping and patios, creating an inviting ambient glow. Natural White (4000K) is great for architectural highlights and clean contemporary surfaces.

11. Is the self-adhesive backing strong enough for outdoor surfaces?

The pre-applied strong adhesive sticks well to smooth, clean surfaces. For rough outdoor wood, stone, or stucco, we recommend using mounting brackets or silicone adhesive clips for permanent security.

12. What is the expected lifespan of this COB LED tape light?

Thanks to efficient COB heat dissipation and high-purity copper traces, MALIIGAZA IP68 LED strips are rated for over 50,000 operational hours.