Shenzhen Cooleeon Electronics Co., Ltd.
MALIIGAZA Solderless COB LED Strip Fast Connector Kit (2Pin/3Pin/4Pin, 5mm/8mm/10mm) - Flame Retardant Plug and Play Jumper Clips
MALIIGAZA Solderless COB LED Strip Fast Connector Kit (2Pin/3Pin/4Pin, 5mm/8mm/10mm) - Flame Retardant Plug and Play Jumper Clips
No se pudo cargar la disponibilidad de retiro
Eliminate delicate wire soldering and frustrating install delays. The MALIIGAZA Solderless COB LED Strip Fast Connector delivers a secure, instantaneous, plug-and-play link for seamless lighting layouts across kitchens, accent channels, and architectural displays.
Seamless COB Lighting Runs Without Soldering Irons or Wire Stripping
Achieving clean, uninterrupted lines of light with COB (Chip on Board) LED strips should not require specialized electrical tools or endless hours spent soldering pad terminals. Cold solder joints, heat-damaged PCB copper pads, and bulky insulation tape can easily compromise your custom illumination project.
The MALIIGAZA FOB-LJQ Series Fast Connector System solves these installation bottlenecks entirely. Engineered specifically for ultra-dense COB flexible tape lights, these compact joiners deliver reliable electrical continuity within seconds. Whether navigating 90-degree corners, bridging cabinet gaps, or extending main power feeds, experience professional-grade connections with a simple press.
Why Professionals Choose MALIIGAZA Solderless Fast Connectors
Zero Soldering & Foolproof Assembly
Forget tedious tinning, hot irons, and melted silicone. Slide your freshly cut COB tape under the precision piercing pins and snap the locking cap shut for an immediate, high-conductivity joint.
Flame-Retardant Safety & Durability
Molded from high-grade, heat-resistant polycarbonate with V-0 flame retardancy, these housings resist thermal expansion, degradation, and electrical arcing far better than cheap PVC alternatives.
Ultra-Compact & Shadowless Profile
Slimline housings sit flush inside standard aluminum channels and diffuser lenses without causing dark spots or unsightly hot-spot shadows across your continuous light stream.
Complete Ecosystem Versatility
Available across 2-Pin (Single Color), 3-Pin (CCT Tunable White), and 4-Pin (RGB) options in 5mm, 8mm, and 10mm PCB widths. Pick exact strip-to-strip, strip-to-wire, L-shape, or T-shape geometries.
Precision Engineering for Low-Voltage COB Architecture
Direct-Contact Piercing Needle Technology
Traditional clip connectors often rely on flat pressure contacts that lose tension over time, leading to flickering lights. MALIIGAZA utilizes copper alloy piercing needles that penetrate directly into the flexible copper circuit board solder pads upon closure. This creates a vibration-proof, low-resistance lock capable of handling steady low-voltage current without power loss.
High-Precision Injection Molded Housings
Off-brand connectors frequently feature sloppy tolerances that slip or crush delicate COB phosphor coatings. MALIIGAZA FOB-LJQ units are precision-cast to match exact PCB widths (5mm ultra-narrow, 8mm standard, and 10mm wide), holding strips securely aligned without pinching adjacent LED chips.
Smart Home & Controller Integration Ready
MALIIGAZA solderless connectors are fully compatible with low-voltage 12V and 24V DC smart lighting drivers, Zigbee dimmers, Wi-Fi controllers, and RGB/CCT smart receivers (Tuya, Philips Hue lightstrip adapters, Smart Life, and Lutron systems). Ensure stable signal transmission across custom-cut COB runs.
Versatile Layout Applications
Under-Cabinet & Shelf Gap Bridging
Use PCB-to-Wire or PCB-to-Wire-to-PCB jumpers to route wiring around range hoods, shelving, and tall kitchen cabinetry without breaks in power.
Seamless 90-Degree Corner Turns
Eliminate sharp, damaging strip bends. Deploy L-shape corner connectors to keep ceiling coves, mirror borders, and TV backlighting crisp and clean.
T-Splitting & Multi-Zone Layouts
Branch a single DC power feed into dual parallel strip runs using T-shape connectors for extensive display cases and wardrobe framing.
Offcut Reuse & Long Run Splicing
Join leftover COB tape segments end-to-end with PCB-to-PCB board couplers, minimizing waste during large-scale installs.
Technical Specifications
| Model Series | MALIIGAZA FOB-LJQ Series |
|---|---|
| Pin Configurations | 2-Pin (Single Color), 3-Pin (CCT Dual White), 4-Pin (RGB) |
| Supported PCB Widths | 5mm, 8mm, 10mm Flexible COB Tape |
| Connection Types | PCB-to-PCB, PCB-to-Wire, Wire-PCB-Wire Jumper, L-Shape, T-Shape |
| Operating Voltage | 5V, 12V, 24V DC Low Voltage Only |
| Max Rated Current | 5A Continuous |
| Housing Material | Flame Retardant Polycarbonate (UL94V-0 Rated) |
| Contact Material | High-Precision Tin-Plated Copper Alloys |
| Ingress Protection | IP20 / IP30 Non-Waterproof (Indoor Environments) |
| Compatibility Standard | Exclusively COB Continuous LED Strips (Non-SMD) |
Package Options & What Is Included
Depending on your selected configuration variant (Pin count, Width, and Connector shape), your package contains:
- Selected Quantity (5-Pack, 10-Pack, or Multi-Kit) of MALIIGAZA COB Fast Connectors
- Pre-attached Extension Wire Leads (for PCB-to-Wire variants only)
- Quick Setup Safety Reference Guide
Step-by-Step Installation Guide
- Cut the COB Strip Correctly: Locate the designated copper pad cut line marked on your COB LED strip. Make a clean, perpendicular cut across the pad using sharp shears.
- Verify Polarity Alignment: Align the positive (+) and negative (-) markings on your COB tape with the corresponding markings on the connector cap and supply wire.
- Insert the Strip: Open the clear locking cap. Slide the end of the COB strip into the connector guide channel until the copper pads lie directly beneath the contact needles.
- Clamp & Secure: Use a pair of standard pliers to press the transparent locking cover down firmly until it snaps flush on both sides.
- Test Continuity: Connect your low-voltage power supply to confirm solid illumination before mounting into channel track.
Troubleshooting Guide
Issue: The LED strip does not light up after closing the clip.
Solution: Check polarity. If positive (+24V or +12V) is crossed with negative (GND), current will not pass. Open the cap, flip the strip direction, and re-clamp. Also verify that the piercing needles fully bit into the copper pads.
Issue: The lights flicker when touching or moving the connector.
Solution: The transparent cover may not be fully clamped. Apply firm pressure with pliers until the side locks engage completely.
Important Usage & Safety Warnings
- Match Polarity Strictly: Always verify positive and negative matching prior to powering on. Reversing polarity prevents system operation.
- Cut Only at Designated Lines: Cut strictly along marked copper pad scissors indicators. Cutting elsewhere will break internal tape circuits.
- COB Strips Only: Designed exclusively for COB flexible LED tape. Not compatible with traditional surface-mount SMD (3528, 5050, 2835) strips due to structural height differences.
- Low Voltage DC Only: Suitable strictly for DC 5V, 12V, or 24V circuits. Never connect to AC 110V/220V main power lines.
- Indoor Dry Locations Only: Ingress rating is IP20/IP30 non-waterproof. Do not submerge or use in unprotected outdoor or high-moisture exterior environments.
- Verify Width Prior to Ordering: Measure your COB tape width carefully (5mm, 8mm, or 10mm) to select matching connector dimensions.
Frequently Asked Questions
1. How do I choose between 2-pin, 3-pin, and 4-pin COB connectors?
Select 2-Pin connectors for single color COB strips (e.g., Warm White, Cool White, Red, Blue). Select 3-Pin connectors for CCT tunable dual-white strips. Select 4-Pin connectors for RGB color-changing COB strips.
2. Can I use these MALIIGAZA solderless connectors with standard SMD LED tape lights?
No. These connectors are engineered specifically for continuous COB (Chip on Board) LED light strips. SMD strips have raised diode chips and different pad heights that interfere with the piercing needle system.
3. Do I need to strip the insulation off extension wires before inserting them into the wire terminal?
No stripping is necessary for wire-to-strip models. The piercing internal teeth bite directly through standard wire insulation into the internal copper wire strands when closed.
4. Will these connectors fit inside narrow aluminum channel tracks?
Yes. MALIIGAZA connectors are engineered with an ultra-slim profile designed to fit inside most standard aluminum extrusion channels with internal widths of 10mm or greater.
5. Are these fast connectors reusable if I make a mistake?
While they are designed for permanent, secure clamping, you can carefully pry open the locking tab using a precision flathead screwdriver to adjust alignment or reposition tape.
6. Can I use these for outdoor or waterproof LED strip setups?
No. These units carry an IP20 non-waterproof rating. They are intended for dry indoor installations. For damp locations, additional heat-shrink tubing or silicone sealant enclosure is required.
7. What maximum wire gauge can be connected to the wire-type connectors?
They support standard 22 AWG to 20 AWG stranded copper extension wire for optimum conductivity and clamping pressure.
8. What happens if I reverse positive and negative during connection?
The LED strip will simply fail to illuminate due to diode polarity protection. It will not damage the strip or connector. Simply flip the polarity orientation.
9. How much current can these connectors safely handle?
They are rated for up to 5 Amps continuous current at low voltage (12V or 24V DC), making them ideal for high-density COB installations up to standard reel lengths.
10. Do these connectors cause light gaps or dark shadows along COB runs?
Because COB tape features continuous phosphor coating, the ultra-narrow housing frame sits extremely tight against the phosphor edge, minimizing any perceptible gap under frosted channel covers.
11. Are MALIIGAZA connectors made of flame retardant plastic?
Yes. All MALIIGAZA housings are molded from UL94V-0 rated flame retardant polycarbonate, providing superior heat safety compared to low-grade PVC connectors.
12. How do I measure my COB LED strip width accurately?
Use a millimeter ruler or digital caliper to measure the outer width of the flexible PCB backing (common sizes are 5mm, 8mm, or 10mm).
Upgrade Your COB LED Installation Today
Stop wasting time with hot soldering irons and unreliable tape. Choose your exact pin count and width to enjoy fast, safe, professional lighting connections.
Select Options & Add to CartFrequently Bought Together
- MALIIGAZA High-Density Flexible COB LED Light Strips (12V/24V) - Spotless continuous linear illumination.
- Recessed & Surface Mount Aluminum LED Channels - Clean protective housing with frosted light diffusers.
- 22 AWG Stranded 2-Conductor / 4-Conductor LED Extension Wire - Oxygen-free copper wiring for custom runs.
