Shenzhen Cooleeon Electronics Co., Ltd.
MALIIGAZA STEP-SP32-PRO Smart Motion Sensor Stair Light Controller with Bluetooth App, 32-Step Control and RGB Side Flow
MALIIGAZA STEP-SP32-PRO Smart Motion Sensor Stair Light Controller with Bluetooth App, 32-Step Control and RGB Side Flow
No se pudo cargar la disponibilidad de retiro
Smart Stair Lighting With Step Lights + RGB Side Flow
The MALIIGAZA STEP-SP32-PRO combines motion-activated individual stair lighting with dynamic RGB side-flow effects in one intelligent controller. Control up to 32 steps, customize each step through the Bluetooth app, and create a more responsive, modern staircase lighting system.
Turn Your Staircase Into a Smart Lighting Experience
Ordinary stair controllers simply switch lights on and off. STEP-SP32-PRO gives you much more control.
When motion is detected, the stair lights can illuminate progressively from the direction you enter while an optional RGB addressable strip creates a synchronized running-light effect along the handrail, wall, or staircase edge.
Why Choose STEP-SP32-PRO?
32 independent step output ports make it suitable for small and large indoor staircases.
Use the app to switch all stair lights on or control individual steps separately.
Add compatible SPI RGB addressable strips for dynamic side-running lighting effects.
Adjust lighting functions conveniently through the compatible Bluetooth mobile app.
Advanced Smart Stair Lighting Features
1. Step-by-Step Lighting + RGB Side Running Effect
Create two lighting effects at the same time. Your stair tread lights can illuminate progressively while a compatible RGB SPI strip runs dynamically along a handrail, wall edge, or staircase side.
2. Dual PIR Motion Detection
Install one PIR motion sensor at the bottom of the staircase and one at the top. Motion detected at the bottom starts the lighting sequence upward, while motion detected at the top starts the sequence downward.
3. Bluetooth App Control
Connect the controller to the compatible mobile app through Bluetooth. Manage operating modes, lighting behavior, individual steps, full-on lighting, speed, timing, and other available settings from your phone.
4. Optional Wireless Remote Control
A compatible wireless remote can be purchased separately for convenient control without opening the app.
5. Up to 32 Independently Controlled Steps
The controller provides 32 stair-light output ports. Each port supports up to 1A, allowing each stair step to be controlled independently.
6. Nine Dynamic Stair Lighting Modes
Choose from 9 dynamic operating modes. Configure sequential step lighting or multi-step effects, then adjust animation speed and lighting duration to match your staircase and preferred visual style.
7. Full-On and Individual Step Control
The app can switch all connected stair lights on continuously or control individual stair outputs separately. This gives DIY users much greater flexibility than conventional motion-only stair controllers.
Lighting Compatibility
Stair step outputs: Compatible with DC12V or DC24V single-color LED strips.
Side-flow output: Compatible with DC12V or DC24V RGB addressable SPI LED strips.
Maximum RGB pixel setting: Up to 1021 pixels.
Important: The side-running output does not support ordinary single-color strips as a running-light strip.
Ideal Applications
Automatic step lighting for modern residential stairs.
Upgrade existing staircases with intelligent motion-activated lighting.
Build a customized step-light and RGB side-flow lighting combination.
Add functional ambient lighting to contemporary indoor spaces.
Technical Specifications
| Model | STEP-SP32-PRO |
| Product Type | Smart stair light controller |
| Input Voltage | DC12V / DC24V |
| Maximum Stair Outputs | 32 |
| Maximum Current Per Stair Port | 1A |
| Step Light Type | 12V / 24V single-color LED strip |
| Side-Flow Light Type | 12V / 24V RGB addressable SPI strip |
| Maximum RGB Pixels | 1021 |
| Control | Bluetooth app + optional wireless remote |
| Motion Detection | Top and bottom PIR sensors |
| Dynamic Modes | 9 stair lighting modes |
| Daylight Sensor | Not included / not supported |
| Waterproof Rating | Non-waterproof - indoor use only |
Package and SKU Selection
This listing is designed as a modular DIY stair lighting system because staircase length, number of steps, LED color, power requirements, and side-flow configurations vary between installations.
Please select the required items from the available SKU options.
- STEP-SP32-PRO stair light controller
- Different colors of stair LED strips
- RGB addressable side-flow LED strip options
- Power supplies
- Extension cables and accessories
- Compatible wireless remote control
Only the item selected in your product variant is included.
Basic Installation Guide
- Determine the number of stair steps and required LED strip length.
- Choose 12V or 24V LED strips and use a power supply with the same voltage.
- Connect each single-color stair strip to the corresponding stair output port.
- Install one PIR sensor near the bottom and one near the top of the staircase.
- If using the side-flow function, connect a compatible RGB addressable SPI LED strip.
- Set the RGB pixel number in the controller settings to match the actual pixel count of the connected addressable strip.
- Power the controller only from a suitable DC12V or DC24V power supply.
Troubleshooting Guide
Stair lights do not turn on
Check the DC power supply, wiring polarity, strip voltage, controller connections, and PIR sensor connections.
Lighting sequence starts in the wrong direction
Check the position and connection of the top and bottom PIR sensors.
RGB side strip does not animate correctly
Confirm that the strip is a compatible RGB addressable SPI strip and verify its operating voltage, signal connection, and pixel number setting.
Only part of the RGB strip responds
Set the pixel number to match the actual number of controllable pixels in the connected strip.
Bluetooth connection is unavailable
Make sure Bluetooth is enabled on your phone and remain near the controller during initial app connection.
Important Safety and Compatibility Notes
- Never connect this controller directly to AC110V, AC120V, AC220V, or AC230V mains electricity.
- The controller must be powered by a suitable DC12V or DC24V power supply.
- The LED strip voltage and power supply voltage must match.
- Never connect a 12V LED strip to a 24V power supply.
- The side-flow function supports RGB addressable SPI LED strips only.
- The side-flow output does not support ordinary single-color strips as running-light strips.
- For RGB addressable strips, set the correct pixel number for accurate lighting control.
- The controller is non-waterproof and intended for indoor use.
- This model does not include a daylight sensor.
- LED strips, power supplies, extension cables, and remote controls are not automatically included unless specifically selected as the purchased SKU.
Frequently Asked Questions
How many stair steps can STEP-SP32-PRO control?
It supports up to 32 individual stair-light outputs.
Can I control each stair light individually?
Yes. Individual stair outputs can be controlled through the compatible Bluetooth app.
Can all stair lights stay on continuously?
Yes. The app supports a full-on function for connected stair lights.
Does this stair controller support Bluetooth app control?
Yes. STEP-SP32-PRO supports Bluetooth connection to a compatible mobile app.
Does it include a wireless remote control?
A compatible wireless remote is optional and must be selected or purchased separately.
What LED strips can I use for the stair steps?
The stair outputs support compatible 12V or 24V single-color LED strips.
What LED strip can I use for the side running light?
Use a compatible 12V or 24V RGB addressable SPI LED strip.
Can I use a single-color strip for the side-flow effect?
No. The dynamic side-flow output is designed for compatible RGB addressable SPI strips.
How many RGB pixels can the controller support?
The RGB side-flow function supports a maximum setting of 1021 pixels.
Why do I need to set the RGB pixel number?
The pixel setting should match the connected strip so the controller can accurately manage the intended lighting area.
How does the motion sensor stair lighting work?
Two PIR sensors detect movement from the top or bottom and start the lighting sequence in the corresponding direction.
Does STEP-SP32-PRO have a daylight sensor?
No. This model does not include a light-sensitive daylight sensor. Operating schedules can instead be configured using the available timing function.
Can I connect the controller directly to household AC power?
No. Never connect it directly to mains electricity. It requires a suitable DC12V or DC24V power supply.
Can I use a 24V power supply with a 12V LED strip?
No. The LED strip and power supply voltage must match.
Is the stair light controller waterproof?
No. STEP-SP32-PRO is non-waterproof and designed for indoor installation.
Are LED strips and power supplies included?
Not automatically. This listing uses separate SKU options so you can build the combination needed for your staircase.
How many dynamic stair lighting modes are available?
The controller provides 9 dynamic stair lighting modes with adjustable operating behavior.
Build Your Own Intelligent Stair Lighting System
Choose the controller, stair strips, RGB side-flow lighting, power supply, and accessories that match your staircase. STEP-SP32-PRO gives you the flexibility to build a clean, responsive, and highly customized indoor lighting system.
Related Product Suggestions
- 12V / 24V COB single-color LED strips for stair steps
- 12V / 24V RGB addressable SPI LED strips for side-flow lighting
- LED power supplies matched to your strip voltage and total load
- Stair light extension cables and wiring accessories
- Compatible wireless stair light remote control
Related Guides
- How to Design a Motion Sensor LED Stair Lighting System
- 12V vs 24V LED Stair Lights: Which Voltage Should You Choose?
- How to Calculate the Right Power Supply for Stair LED Lighting
- How RGB Addressable SPI LED Strips Work in Staircase Lighting
- How to Plan LED Wiring for a 16, 20, 24, or 32-Step Staircase
